Home |
About |
FAQ |
Shipping Policies |
Extras and Deals |
Custom Options |
Contact Us
Foam Tool Organizer for
18 Tekton Screwdriver Set
Overview
18 Tekton Screwdriver Set
Fits (6) slotted, (6) phillips, and (6) torx screwdrivers.
Accommodates the high-torque black oxide screwdrivers from set DRV41216 and torx DHT91006. Also fits screwdrivers with chrome blades.
May be trimmed to fit a variety of drawer sizes.
Drawer Size
24 X 18 inches
$59.90
Details
- Drawer size: 24 X 18 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 18 Tekton screwdrivers:
slotted:
1/4 X 1-1/2 (Tekton 26621 or DHS30250)
1/8 X 4 (Tekton 26603 or DHS31125)
3/16 X 4 (Tekton 26613 or DHS31188)
1/4 X 4 (Tekton 26623 or DHS31250)
3/16 X 8 (Tekton 26615 or DHS34188)
1/4 X 8 (Tekton 26625 or DHS34250)
phillips:
#2 X 1-1/2 (Tekton 26671 or DHP30002)
#0 X 4 (Tekton 26653 or DHP31000)
#1 X 4 (Tekton 26663 or DHP31001)
#2 X 4 (Tekton 26673 or DHP31002)
#1 X 8 (Tekton 26665 or DHP34001)
#2 X 8 (Tekton 26675 or DHP34002)
torx:
T10 X 4 (Tekton 26801 or DHT31100)
T15 X 4 (Tekton 26802 or DHT31150)
T20 X 4 (Tekton 26803 or DHT31200)
T25 X 4 (Tekton 26804 or DHT31250)
T27 X 4 (Tekton 26805 or DHT31270)
T30 X 4 (Tekton 26806 or DHT31300)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit the 18 Tekton screwdrivers from black oxide sets DRV41216 and DHT91006 or chrome sets DRV43007 and DHT43001.
Possible Modifications
Minimum trimmable size:
21-5/8 X 14 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
Contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-03575-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
