Fits the crow foot wrenches from set WCF93302. Also fits a 3/8-drive ratchet SRH11108, 3/8 X 3 extension, and 10-80 ft-lb torque wrench 24330.
Fits (13) inch sizes from 5/16 to 1, (17) metric sizes from 8 to 24 mm, and (3) additional tools.
Only fits the newer crow foot wrenches made in the USA.
Recommended for 2-7/16 min drawer height.
Drawer Size
11-7/8 X 17-3/4 inches
$44.60
larger image
note: tools are not included
Precision CNC-cut to fit 33 Tekton tools:
5/16 (Tekton WCF13108)
11/32 (Tekton WCF13109)
3/8 (Tekton WCF13110)
7/16 (Tekton WCF13111)
1/2 (Tekton WCF13113)
9/16 (Tekton WCF13114)
5/8 (Tekton WCF13116)
11/16 (Tekton WCF13117)
3/4 (Tekton WCF13119)
13/16 (Tekton WCF13121)
7/8 (Tekton WCF13122)
15/16 (Tekton WCF13124)
1 (Tekton WCF13125)
8 mm (Tekton WCF14108)
9 mm (Tekton WCF14109)
10 mm (Tekton WCF14110)
11 mm (Tekton WCF14111)
12 mm (Tekton WCF14112)
13 mm (Tekton WCF14113)
14 mm (Tekton WCF14114)
15 mm (Tekton WCF14115)
16 mm (Tekton WCF14116)
17 mm (Tekton WCF14117)
18 mm (Tekton WCF14118)
19 mm (Tekton WCF14119)
20 mm (Tekton WCF14120)
21 mm (Tekton WCF14121)
22 mm (Tekton WCF14122)
23 mm (Tekton WCF14123)
24 mm (Tekton WCF14124)
10-80 ft-lb, 3/8-drive torque wrench (Tekton 24330)
3/8 X 8 ratchet (Tekton SRH11108)
3/8 X 3 extension (Tekton SHA11103)
This tool organizer was designed to fit the Tekton 30-pc crow foot wrench set plus 3 additional tools. Model numbers for the crow foot set include WCF93302, WCF94302, or WCF95301. Only fits newer crow foot wrenches with USA marked on them. The 3 added tools are 3/8-drive torque wrench 24330, 3/8 ratchet SRH11108, and 3/8 X 3 extension SHA11103.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
11-7/8 X 17-3/4 inches (inside width by inside depth)
Recommended for a drawer with at least 2-7/16 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
10-5/8 X 16 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.