Contact Us | Drawing and Part Number Lookup 920-569-0140
210 Craftsman Sockets
Fits (76) 1/4-drive sockets,
and (134) 3/8-drive sockets.
Accommodates all 1/4 and 3/8-drive sockets from the 540-piece Craftsman set 36540.
Caution: Recommended for a 3-inch or deeper drawer.
22-1/4 X 14-1/2 inches
(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(12) 1/4-drive 6-point sizes from 4 to 14
(10) 1/4-drive 12-point sizes from 3/16 to 9/16
(10) 1/4-drive 6-point deep sizes from 3/16 to 9/16
(11) 1/4-drive 6-point deep sizes from 4 to 14
(10) 1/4-drive 12-point deep sizes from 3/16 to 9/16
(5) 1/4-drive hex bit sizes from 3/16 to 3/8
(2) 1/4-drive slotted screwdriver bits from 3/32 to 1/4
(2) 1/4-drive Phillips screwdriver bits from P1 to P2
(3) 1/4-drive Torx screwdriver bits from T15 to T25
(13) 3/8-drive 6-point sizes from 1/4 to 1
(17) 3/8-drive 6-point sizes from 6 to 22
(5) 3/8-drive 8-point sizes from 1/4 to 1/2
(13) 3/8-drive 12-point sizes from 1/4 to 1
(13) 3/8-drive 12-point sizes from 8 to 19 plus 21
(11) 3/8-drive 6-point deep sizes from 3/8 to 1
(11) 3/8-drive 6-point deep sizes from 9 to 19
(11) 3/8-drive 12-point deep sizes from 3/8 to 1
(13) 3/8-drive 12-point deep sizes from 9 to 19 plus 21 and 22
(6) 3/8-drive hex bit sizes from 5/32 to 3/8
(6) 3/8-drive hex bit sizes from 4 to 8 plus 10
(3) 3/8-drive slotted screwdriver bits from 7/32 to 3/8
(4) 3/8-drive Phillips screwdriver bits from P1 to P4
(4) 3/8-drive Torx screwdriver bits from T30 to T50
(3) 3/8-drive spark plug sockets from 5/8 to 13/16
(1) 3/8-drive spark plug socket 18
This tool organizer was designed to fit all 1/4 and 3/8-drive sockets from the Craftsman 540-piece set 36540. The pockets are sized to fit sockets with "U.S.A." markings.
21-1/2 X 14 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.