FoamFit Tools section divider

Foam Tool Organizer for
3 Craftsman Teardrop Ratchets with Magnetic Bit Set and Ignition Wrenches

see all organizers for ratchets and drive tools


3 Craftsman Teardrop Ratchets with Magnetic Bit Set and Ignition Wrenches

Fits (3) ratchets,
(6) extensions,
(1) magnetic handle,
(9) screwdriver bits,
(1) adapter,
(12) nut driver bits,
(10) inch ignition wrenches,
and (10) metric ignition wrenches.

Accommodates the ratchets, drive tools, and ignition wrenches from the older version of the 309-piece mechanics tool set 41309.

Drawer Size
22-1/4 X 10-5/8 inches


FoamFit Tools section divider


1/2-drive quick release teardrop ratchet (Craftsman 44809)
3/8-drive quick release long teardrop ratchet (Craftsman 44808)
1/4-drive quick release teardrop ratchet (Craftsman 44807)
1-1/2-inch extension bar, 1/4-drive (Craftsman 43538)
3-inch extension bar, 1/4-drive (Craftsman 43539)
1-1/2-inch extension bar, 3/8-drive (Craftsman 43537)
3-inch extension bar, 3/8-drive (Craftsman 44264)
6-inch extension bar, 3/8-drive (Craftsman 44261)
3-inch extension bar, 1/2-drive (Craftsman 44133)
Magnetic Bit Handle (Craftsman 43373)
(3) Slotted Screwdriver Bits: 5/16, 1/4, 9/32
(3) Phillips Screwdriver Bits: P1, P2, P3
(2) Torx Screwdriver Bits: T15, T20
(1) Square Screwdriver Bit: R2
(1) Adapter Bit, Magnetic Handle to 1/4-Drive Socket
(7) Nut Driver Bits, Inch Sizes: 3/16, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16
(5) Nut Driver Bits, Metric Sizes: 5, 6, 8, 10, 11
(10) Inch Ignition Wrenches: 5/32 to 7/16 (Craftsman 42320 to 42329)
(10) Metric Ignition Wrenches: 4mm to 11mm (Craftsman 42340 to 42349)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for Craftsman Ratchets, Extensions, Drive Tools, and Ignition Wrenches from the 309-Piece Mechanics Tool Set

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the ratchets, drive tools, and ignition wrenches from the Craftsman 309-piece set 41309. The pockets are sized to fit older tools which have "U.S.A." markings.

Possible Modifications

Minimum trimmable size:

21-3/4 X 10-3/8 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site