Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
21 Craftsman Open End and Flare-Nut Wrenches
Overview
21 Craftsman Open End and Flare-Nut Wrenches
Fits (6) inch open-end wrenches,
(4) inch flare-nut wrenches,
(6) metric open-end wrenches,
and (5) metric flare-nut wrenches.
Note: This organizer fits the open-end and flare-nut wrenches from the Craftsman 300-piece basic essential pro set (see Craftsman 33300).
Caution: Only fits the older Craftsman wrenches marked "U.S.A." Newer Craftsman wrenches will not fit because they have some width and length differences.
Drawer Size
22-1/4 X 16-1/4 inches
$53.40
Details
- Drawer size: 22-1/4 X 16-1/4 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 21 Craftsman wrenches:
inch open end wrenches:
1/4 X 5/16, 3/8 X 7/16, 1/2 X 9/16, 9/16 X 5/8, 5/8 X 3/4, 3/4 X 7/8
inch flare-nut wrenches:
3/8 X 7/16, 1/2 X 9/16, 5/8 X 11/16, 3/4 X 7/8
metric open end wrenches:
6 X 8, 7 X 9, 10 X 11, 12 X 14, 13 X 15, 16 X 18
metric flare-nut wrenches:
9 X 11, 10 X 12, 13 X 14, 15 X 17, 19 X 21
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit the open end and flare-nut wrenches from the Craftsman 300-piece basic essentials pro set (33300). The pockets fit the older raised-panel wrenches which have "U.S.A." markings. Wrenches lacking this mark will not fit.
Possible Modifications
Minimum trimmable size:
21-3/4 X 16 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1M-00680.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
