FoamFit Tools section divider

Foam Tool Organizer for
16 Craftsman Flat Full-Polish Ratcheting Wrenches with 20 Ignition Wrenches

see all organizers for ratcheting wrenches


16 Craftsman Flat Full-Polish Ratcheting Wrenches with 20 Ignition Wrenches

Fits (8) non-reversible inch ratcheting wrenches, (8) non-reversible metric ratcheting wrenches, (10) inch ignition wrenches, and (10) metric ignition wrenches.

Accommodates all wrenches from the 334-piece mechanics tool set 35334.

Drawer Size
22-1/4 X 14-1/2 inches


FoamFit Tools section divider


inch flat full-polish ratcheting wrenches:
5/16 (Craftsman 42560)
3/8 (Craftsman 42561)
7/16 (Craftsman 42562)
1/2 (Craftsman 42563)
9/16 (Craftsman 42564)
5/8 (Craftsman 42565)
11/16 (Craftsman 42566)
3/4 (Craftsman 42567)

inch ignition wrenches:
5/32 (Craftsman 42320)
3/16 (Craftsman 42321)
13/64 (Craftsman 42322)
7/32 (Craftsman 42323)
15/64 (Craftsman 42324)
1/4 (Craftsman 42325)
9/32 (Craftsman 42326)
5/16 (Craftsman 42327)
3/8 (Craftsman 42328)
7/16 (Craftsman 42329)

metric flat full-polish ratcheting wrenches:
8mm (Craftsman 42568)
10mm (Craftsman 42569)
12mm (Craftsman 42570)
13mm (Craftsman 42571)
14mm (Craftsman 42572)
15mm (Craftsman 42573)
17mm (Craftsman 42575)
18mm (Craftsman 42576)

metric ignition wrenches:
4mm (Craftsman 42340)
4.5mm (Craftsman 42341)
5mm (Craftsman 42342)
5.5mm (Craftsman 42343)
6mm (Craftsman 42344)
7mm (Craftsman 42345)
8mm (Craftsman 42346)
9mm (Craftsman 42347)
10mm (Craftsman 42348)
11mm (Craftsman 42349)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for Craftsman Flat, Full-Polish, Non-Reversible Ratcheting Wrenches and Ignition Wrenches

note: tools are not included

Tool Requirements

This organizer only fits Craftsman full-polish ratcheting wrenches without reversing levers. This organizer fits the ratcheting wrenches and ignition wrenches included in the Craftsman 334-piece mechanics tool set 35334.

Possible Modifications

Minimum trimmable size:

21-3/4 X 14-1/4 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site