FoamFit Tools section divider

Foam Tool Organizer for
75 Craftsman 1/4-drive Sockets with Ratchet, Extensions, and Magnetic Bit Set

see all organizers for sockets

Overview

75 Craftsman 1/4-drive Sockets with Ratchet, Extensions, and Magnetic Bit Set

Fits (41) inch 1/4-drive sockets,
(23) metric 1/4-drive sockets,
(5) hex bit sockets,
(3) torx bit sockets,
(3) external torx sockets,
(1) ratchet,
(2) extensions,
(1) magnetic handle,
and (22) magnetic bits.

Accommodates the 1/4-drive sockets and drive tools from the 334-piece mechanics tool set 35334.

Drawer Size
22-1/4 X 16-1/4 inches

$53.40



FoamFit Tools section divider

Details

(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(10) 1/4-drive 12-point sizes from 3/16 to 9/16
(10) 1/4-drive 6-point deep sizes from 3/16 to 9/16
(10) 1/4-drive 12-point deep sizes from 3/16 to 9/16
(12) 1/4-drive 6-point sizes from 4 to 14
(11) 1/4-drive 6-point deep sizes from 4 to 14
(5) 1/4-drive hex bit sizes from 3/16 to 3/8
(3) 1/4-drive Torx screwdriver bits from T15 to T25
(3) 1/4-drive external Torx sockets from E6 to E8
1/4-drive quick release teardrop ratchet (Craftsman 44807)
1-1/2-inch extension bar, 1/4-drive (Craftsman 43538)
3-inch extension bar, 1/4-drive (Craftsman 43539)
magnetic handle (Craftsman 43373)
(7) inch nut driver bits
(5) metric nut driver bits
(9) screwdriver bits
(1) adapter bit for 1/4-drive sockets

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for Craftsman 1/4-drive Sockets, Extensions, and Ratchet

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the 1/4-drive sockets and drive tools from the Craftsman 334-piece set 35334. The pockets are sized to fit sockets that don't have "U.S.A." markings.

Possible Modifications

Minimum trimmable size:

21-3/4 X 11-1/4 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F1M-00988.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site