Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
178 Craftsman Industrial Sockets
Overview
178 Craftsman Industrial Sockets
Fits (48) 1/4-drive sockets,
(92) 3/8-drive sockets,
and (38) 1/2-drive sockets.
Accommodates all sockets from the Craftsman Industrial 255-piece mechanics tool set 29794.
Caution: Recommended for a 4-inch or deeper drawer.
Drawer Size
22-1/4 X 16-1/4 inches
$70.90
Details
- Drawer size: 22-1/4 X 16-1/4 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 178 Craftsman Industrial sockets:
(10) 1/4-drive 6-point sizes from 5/32 to 1/2
(9) 1/4-drive 12-point sizes from 3/16 to 1/2
(9) 1/4-drive 6-point deep sizes from 3/16 to 1/2
(11) 3/8-drive 6-point sizes from 3/8 to 1
(10) 3/8-drive 12-point sizes from 5/16 to 7/8
(9) 3/8-drive 6-point deep sizes from 3/8 to 7/8
(8) 3/8-drive 12-point deep sizes from 3/8 to 13/16
(7) 3/8-drive hex bit sizes from 1/8 to 3/8
(3) 3/8-drive spark plug sizes 5/8, 13/16, 13/16 flex
(13) 1/2-drive 12-point sizes from 7/16 to 1-1/4
(4) 1/2-drive 6-point deep sizes 9/16, 3/4, 15/16, and 1-1/16
(9) 1/2-drive 12-point deep sizes from 1/2 to 1
(10) 1/4-drive 6-point sizes from 4 to 13
(10) 1/4-drive 6-point deep sizes from 4 to 13
(11) 3/8-drive 6-point sizes from 7 to 15 plus 17 and 19
(10) 3/8-drive 12-point sizes from 9 to 18
(7) 3/8-drive 6-point deep sizes 10, 12 to 15, 18, and 19
(8) 3/8-drive 12-point deep sizes from 9 to 16
(6) 3/8-drive hex bit sizes from 4 to 8 plus 10
(2) 3/8-drive torx sizes T-40 and T-55
(12) 1/2-drive 12-point sizes 10 to 15, 18, 19, and 21 to 24
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit the sockets from the Craftsman Industrial 255-piece set 29794.
Possible Modifications
Minimum trimmable size:
21-3/4 X 14-5/8 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1A-01100.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
