Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
19 Craftsman Inch and Metric Box Wrenches, Fits non-USA Version 3
Overview
19 Craftsman Inch and Metric Box Wrenches, Fits non-USA Version 3
Fits (9) inch box wrenches,
(9) metric box wrenches,
and (1) inch obstruction wrench.
Note: this organizer fits all the box wrenches from version 3 of the Craftsman 540-piece mechanics tool set (see Craftsman 35540).
Caution: see note about wrench length.
Drawer Size
22-1/4 X 16-1/4 inches
$53.40
Details
- Drawer size: 22-1/4 X 16-1/4 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 19 Craftsman box wrenches:
inch wrenches: 1/4 X 5/16, 3/8 X 7/16, 7/16 X 1/2, 1/2 X 9/16, 9/16 X 5/8, 5/8 X 3/4, 11/16 X 13/16, 3/4 X 7/8, 15/16 X 1
obstruction wrench: 9/16 X 5/8
metric wrenches: 6 X 8, 7 X 9, 10 X 11, 12 X 14, 13 X 15, 16 X 18, 17 X 19, 20 X 22, 21 X 23
Note about wrench length:
Some of the 540-piece sets produced under Craftsman model number 35540 have a shorter 3/8 X 7/16 box wrench that will not fit in this organizer. Download the drawing below to check the fit, or measure the 3/8 X 7/16 box wrench in your set. The length of the 3/8 X 7/16 wrench should be approximately 8-1/2 inches long.
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit the box wrenches from version 3 of the Craftsman 540-piece set (see Craftsman 35540). The pockets are sized to fit tools that don't have "USA" markings.
Possible Modifications
Minimum trimmable size:
22 X 16 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1M-01107.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
