Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
89 Craftsman 3/8-drive Sockets with Ratchet and Extensions
Overview
89 Craftsman 3/8-drive Sockets with Ratchet and Extensions
Fits (36) inch 3/8-drive sockets,
(43) metric 3/8-drive sockets,
(10) hex bit sockets,
(1) ratchet,
and (3) extensions.
Accommodates the 3/8-drive sockets and drive tools from the 311-piece mechanics tool set 35311.
Caution: Recommended for a 3-inch or deeper drawer.
Drawer Size
22-1/4 X 10-5/8 inches
$51.50
Details
- Drawer size: 22-1/4 X 10-5/8 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 89 Craftsman sockets and additional tools:
(13) 3/8-drive 6-point sizes from 1/4 to 1
(5) 3/8-drive 8-point sizes from 1/4 to 1/2
(10) 3/8-drive 12-point sizes from 1/4 to 13/16
(8) 3/8-drive 12-point deep sizes from 3/8 to 7/8
(17) 3/8-drive 6-point sizes from 6 to 22
(15) 3/8-drive 12-point sizes from 6 to 19 plus 21
(11) 3/8-drive 12-point deep sizes from 9 to 19
(5) 3/8-drive hex bit sizes from 5/32 to 5/16
(5) 3/8-drive hex bit sizes from 4 to 8
3/8-drive 75-tooth full-polish ratchet (Craftsman 20722 or 49203)
1-1/2-inch extension bar, 3/8-drive (Craftsman 43537)
3-inch extension bar, 3/8-drive (Craftsman 44264)
6-inch extension bar, 3/8-drive (Craftsman 44261)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit the 3/8-drive sockets and drive tools from the Craftsman 311-piece set 35311. The pockets are sized to fit sockets that don't have "U.S.A." markings.
Possible Modifications
Minimum trimmable size:
21-5/8 X 9-1/4 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1A-01255.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
