Fits (10) non-reversible inch ratcheting wrenches and (10) non-reversible metric ratcheting wrenches.
Accommodates the full-polish ratcheting wrenches from version 1 of set 41220 or 46820.
Only fits the longer version without USA markings. See details for wrench lengths.
22-1/4 X 14-1/2 inches
note: tools are not included
Precision CNC-cut to fit 20 Craftsman wrenches:
inch flat full-polish ratcheting wrenches:
1/4 (Craftsman 39230), 5 inches long
5/16 (Craftsman 42560), 5-13/16 inches long
11/32 (Craftsman 47613), 6-1/4 inches long
3/8 (Craftsman 42561), 6-3/4 inches long
7/16 (Craftsman 42562), 7-3/8 inches long
1/2 (Craftsman 42563), 8-1/4 inches long
9/16 (Craftsman 42564), 8-13/16 inches long
5/8 (Craftsman 42565), 9-5/8 inches long
11/16 (Craftsman 42566), 10-1/8 inches long
3/4 (Craftsman 42567), 11-1/8 inches long
metric flat full-polish ratcheting wrenches:
6mm (Craftsman 39240), 5 inches long
8mm (Craftsman 42568), 5-7/8 inches long
10mm (Craftsman 42569), 6-3/4 inches long
12mm (Craftsman 42570), 7-13/16 inches long
13mm (Craftsman 42571), 8-5/16 inches long
14mm (Craftsman 42572), 8-3/4 inches long
15mm (Craftsman 42573), 9-1/4 inches long
16mm (Craftsman 39238), 9-9/16 inches long
17mm (Craftsman 42575), 10-1/4 inches long
18mm (Craftsman 42576), 10-11/16 inches long
This tool organizer was designed to fit version 1 of the 20-Piece Craftsman ratcheting wrench set 41220 or 46820. The pockets fit full-polish, non-reversible wrenches that do not have "U.S.A." markings. This organizer only fits the longer version of these wrenches, so please verify your wrench lengths before ordering.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
22-1/4 X 14-1/2 inches (inside width by inside depth)
Works in most drawers, needing no more than 2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
21-3/4 X 14-1/4 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.
For orders within the contiguous 48 US states.
Made in the USA!