Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
66 Craftsman 1/2-drive Sockets with Ratchet and Extensions
Overview
66 Craftsman 1/2-drive Sockets with Ratchet and Extensions
Fits (31) inch 1/2-drive sockets,
(33) metric 1/2-drive sockets,
(2) spark plug sockets,
(1) ratchet,
(2) extensions,
and (1) swivel.
Accommodates the 1/2-drive sockets and drive tools from the Craftsman 348-piece set 49348.
Drawer Size
22-1/4 X 14-1/2 inches
$49.80
Details
- Drawer size: 22-1/4 X 14-1/2 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 66 Craftsman sockets and additional tools:
(9) 1/2-drive 6-point sizes from 3/8 to 7/8
(13) 1/2-drive 12-point sizes from 3/8 to 1-1/8
(9) 1/2-drive 12-point deep sizes from 1/2 to 1
(2) 1/2-drive spark plug socket sizes 5/8, 13/16
(14) 1/2-drive 6-point sizes from 9 to 22
(10) 1/2-drive 12-point sizes 9, 10, and 12 to 19
(9) 1/2-drive 12-point deep sizes from 13 to 21
1/2-drive thin-profile ratchet (Craftsman 44996)
3-inch extension bar, 1/2-drive (Craftsman 44133)
6-inch extension bar, 1/2-drive (Craftsman 44131)
1/2-drive universal joint (Craftsman 04425)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit the 1/2-drive sockets, ratchet, and drive tools from the Craftsman 348-piece set 49348. The pockets are sized to fit tools that don't have "U.S.A." markings.
Possible Modifications
Minimum trimmable size:
21-3/4 X 14-1/4 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1M-01456.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
