Contact Us | Drawing and Part Number Lookup 920-569-0140
165 Snap-on Sockets with 4 Ratchets and 17 Drive Accessories
Fits (84) inch sockets, (81) metric sockets, (4) ratchets, and (17) drive accessories.
30-1/2 X 21-7/8 inches
1/4-Drive Dual 80 Standard Handle Ratchet (Snap-on T72)
1/4 X 2 Extension (Snap-on TMXK2)
1/4 X 6 Extension (Snap-on TMXK60)
1/4-Drive Spinner Handle (Snap-on TM4CSA)
1/4-Drive Universal Joint (Snap-on TMU8B)
(10) 1/4-drive 6-point sizes from 3/16 to 9/16
(10) 1/4-drive 6-point deep sizes from 3/16 to 9/16
(10) 1/4-drive 6-point sizes from 5.5 to 14 mm
(10) 1/4-drive 6-point deep sizes from 5.5 to 14 mm
(4) 1/4-drive hex bit sizes from 1/16 to 7/64
3/8-Drive Dual 80 Standard Handle Ratchet (Snap-on F80)
3/8-Drive Dual 80 Long Handle Ratchet (Snap-on FL80)
3/8 X 1-1/2 Extension (Snap-on FX1)
3/8 X 3 Extension (Snap-on FXK3)
3/8 X 6 Extension (Snap-on FXK6)
3/8 X 8 Extension (Snap-on FXK8)
3/8 X 11 Extension (Snap-on FXK11)
3/8 X 12 Long Handle Breaker Bar (Snap-on F12LB)
3/8-Drive Universal Joint (Snap-on FU8A)
(12) 3/8-drive 6-point sizes from 1/4 to 7/8 including 11/32
(12) 3/8-drive 6-point deep sizes from 1/4 to 7/8 including 11/32
(12) 3/8-drive 6-point sizes from 8 to 19 mm
(12) 3/8-drive 6-point deep sizes from 8 to 19 mm
(2) 3/8-drive spark plug sizes 5/8 and 13/16 (Snap-on S9704KA, S9706KA) (8) 3/8-drive hex bit sizes from 1/8 to 3/8
(11) 3/8-drive hex bit sizes from 4 to 14 mm
1/2-Drive Dual 80 Standard Handle Ratchet (Snap-on S80A)
1/2 X 3-1/2 Extension (Snap-on SXK3)
1/2 X 5 Extension (Snap-on SXK5)
1/2 X 10 Extension (Snap-on SXK10)
1/2 X 18 Standard Handle Breaker Bar (Snap-on SN18B)
1/2-Drive Universal Joint (Snap-on S8)
(13) 1/2-drive 6-point sizes from 3/8 to 1-1/8
(13) 1/2-drive 6-point deep sizes from 3/8 to 1-1/8
(13) 1/2-drive 6-point sizes from 12 to 24 mm
(13) 1/2-drive 6-point deep sizes from 12 to 24 mm
29-3/4 X 19-7/8 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.