Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
32 Craftsman Combination Wrenches, Fits Full-Polish non-USA Wrenches
Overview
32 Craftsman Combination Wrenches, Fits Full-Polish non-USA Wrenches
Fits (11) full-polish wrenches from 11/32 to 15/16, (5) ignition wrenches from 3/16 to 7/16, (11) full-polish wrenches from 9 to 19 mm, and (5) ignition wrenches from 5 to 9 mm.
Accommodates the wrenches from the Craftsman 32-piece wrench set 45032.
Caution: Recommended for a 2-1/2 inch or deeper drawer.
Drawer Size
22-1/4 X 16-1/4 inches
$70.90
Details
- Drawer size: 22-1/4 X 16-1/4 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 32 Craftsman wrenches:
inch combination wrench sizes:
11/32 (Craftsman 47982)
3/8 (Craftsman 45975)
7/16 (Craftsman 45976)
1/2 (Craftsman 45977)
9/16 (Craftsman 45978)
5/8 (Craftsman 45979)
11/16 (Craftsman 45980)
3/4 (Craftsman 45981)
13/16 (Craftsman 45982)
7/8 (Craftsman 45983)
15/16 (Craftsman 45984)
inch ignition (midget) wrench sizes:
3/16, 1/4, 5/16, 3/8, 7/16
metric combination wrench sizes:
9 (Craftsman 45988)
10 (Craftsman 45989)
11 (Craftsman 45990)
12 (Craftsman 45991)
13 (Craftsman 45992)
14 (Craftsman 45993)
15 (Craftsman 45994)
16 (Craftsman 45995)
17 (Craftsman 45996)
18 (Craftsman 45997)
19 (Craftsman 45998)
metric ignition (midget) wrench sizes:
5, 6, 7, 8, 9
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit the full-polish wrenches from the Craftsman 32-piece wrench set 45032. The pockets only fit full-polish wrenches that don't have "USA" markings.
Possible Modifications
Minimum trimmable size:
21-5/8 X 14-1/4 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1A-01593.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
