FoamFit Tools section divider

Foam Tool Organizer for
134 Craftsman Inch Sockets, Fits non-USA Sockets

see all organizers for sockets


134 Craftsman Inch Sockets, Fits non-USA Sockets

Fits (41) 1/4-drive sockets,
(53) 3/8-drive sockets,
and (40) 1/2-drive sockets.

Accommodates all inch sockets from the 299-piece Craftsman socket set 35299 except the 1/2-drive deep sockets.

Caution: Recommended for a 3-inch or deeper drawer.

Pockets sized to fit the 2nd version of this set.

Drawer Size
22-1/4 X 16-1/4 inches


FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 134 Craftsman sockets:

(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(10) 1/4-drive 12-point sizes from 3/16 to 9/16
(10) 1/4-drive 6-point deep sizes from 3/16 to 9/16
(10) 1/4-drive 12-point deep sizes from 3/16 to 9/16
(13) 3/8-drive 6-point sizes from 1/4 to 1
(5) 3/8-drive 8-point sizes from 1/4 to 1/2
(13) 3/8-drive 12-point sizes from 1/4 to 1
(11) 3/8-drive 6-point deep sizes from 3/8 to 1
(11) 3/8-drive 12-point deep sizes from 3/8 to 1
(15) 1/2-drive 6-point sizes from 3/8 to 1-1/4
(6) 1/2-drive 8-point sizes from 7/16 to 3/4
(19) 1/2-drive 12-point sizes from 3/8 to 1-1/2

This tool organizer was designed to fit most of the inch sockets from the Craftsman 299-piece set 35299. The pockets are sized to fit the 2nd version of the set. The sockets don't have "U.S.A." markings, and the 1/2-drive deep sockets are 3.25 inches long.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for Craftsman Inch Sockets

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

22-1/4 X 16-1/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 22 X 15-11/16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site