Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
25 Craftsman Metric Combination Wrenches, Fits non-USA Wrenches
Overview
25 Craftsman Metric Combination Wrenches, Fits non-USA Wrenches
Fits (25) raised-panel wrenches from 6 to 28 mm plus 30 and 32 mm.
Accommodates the metric combination wrenches from the Craftsman 43-pc wrench set 44048 or 63-pc wrench set 41232.
Caution: Recommended for a 3 inch or deeper drawer.
Drawer Size
22-1/4 X 16-1/4 inches
$70.90
Details
- Drawer size: 22-1/4 X 16-1/4 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 25 Craftsman wrenches:
metric combination wrench sizes:
6 (Craftsman 42909)
7 (Craftsman 42911)
8 (Craftsman 42912)
9 (Craftsman 42913)
10 (Craftsman 42914)
11 (Craftsman 42915)
12 (Craftsman 42916)
13 (Craftsman 42917)
14 (Craftsman 42918)
15 (Craftsman 42919)
16 (Craftsman 42924)
17 (Craftsman 42929)
18 (Craftsman 42925)
19 (Craftsman 42921)
20 (Craftsman 42937)
21 (Craftsman 42938)
22 (Craftsman 42922)
23 (Craftsman 42939)
24 (Craftsman 42923)
25 (Craftsman 42931)
26 (Craftsman 42932)
27 (Craftsman 42933)
28 (Craftsman 42934)
30 (Craftsman 42935)
32 (Craftsman 42936)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit raised-panel wrenches from the Craftsman 43-pc wrench set 44048 or the 63-pc wrench set 41232. The pockets are sized to fit wrenches that don't have "USA" markings.
Possible Modifications
Minimum trimmable size:
21-1/8 X 15-3/8 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1A-01855.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
