Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
18 Craftsman Inch Combination Wrenches with 20 Ignition Wrenches
Overview
18 Craftsman Inch Combination Wrenches with 20 Ignition Wrenches
Fits (18) raised-panel wrenches from 1/4 to 1-5/16 plus (10) inch and (10) metric ignition wrenches.
Accommodates the inch combination wrenches and the ignition wrenches from the Craftsman 63-pc wrench set 41232.
Caution: Recommended for a 3 inch or deeper drawer.
Drawer Size
22-1/4 X 16-1/4 inches
$70.90
Details
- Drawer size: 22-1/4 X 16-1/4 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 38 Craftsman wrenches:
inch combination wrench sizes:
1/4 (Craftsman 44699)
5/16 (Craftsman 44691)
11/32 (Craftsman 44692)
3/8 (Craftsman 44693)
7/16 (Craftsman 44694)
1/2 (Craftsman 44695)
9/16 (Craftsman 44696)
5/8 (Craftsman 44697)
11/16 (Craftsman 44698)
3/4 (Craftsman 44701)
13/16 (Craftsman 44702)
7/8 (Craftsman 44703)
15/16 (Craftsman 44704)
1 (Craftsman 44705)
1-1/16 (Craftsman 44706)
1-1/8 (Craftsman 44707)
1-1/4 (Craftsman 44708)
1-5/16 (Craftsman 44709)
inch ignition wrench sizes:
5/32, 3/16, 13/64, 7/32, 15/64, 1/4, 9/32, 5/16, 3/8, 7/16
metric ignition wrench sizes:
4, 4.5, 5, 5.5, 6, 7, 8, 9, 10, 11
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit raised-panel combination and ignition wrenches from the Craftsman 63-pc wrench set 41232. The pockets are sized to fit wrenches that don't have "USA" markings.
Possible Modifications
Minimum trimmable size:
21-3/4 X 16 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1A-01865.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
