FoamFit Tools section divider

Foam Tool Organizer for
8 Craftsman Extreme Grip Sockets with 60 Additional Tools

see all organizers for sockets


8 Craftsman Extreme Grip Sockets with 60 Additional Tools

Fits (8) 3/8-drive extreme grip sockets, (38) screwdriver bits, (2) gimbal palm ratchets, (16) folding hex keys, (2) pliers, magnetic handle, and 3/8 adapter.

Accommodates the extreme grip style sockets from the Craftsman 903-pc set 21470.

Only fits the older Craftsman pliers with USA markings.

Drawer Size
11-1/2 X 16-1/4 inches


FoamFit Tools section divider


extreme grip socket sizes:
3/8, 10mm (Craftsman 41882)
15/32, 12mm (Craftsman 41883)
7/16, 11mm (Craftsman 27028)
1/2, 13mm (Craftsman 27069)
9/16, 14mm (Craftsman 27220)
5/8, 16mm (Craftsman 27221)
11/16, 17mm (Craftsman 27240)
3/4, 19mm (Craftsman 41884)

1/4-drive gimbal palm ratchet (Craftsman 12625)
3/8-drive gimbal palm ratchet (Craftsman 12626)
magnetic handle (Craftsman 43373)
(30) screwdriver bits with 1/4-inch hex body
(8) screwdriver bits with 3/8 (10mm) hex body
3/8-drive to hex bit adapter (Craftsman 17147)
long nose pliers (Craftsman 45102)
slip-joint pliers (Craftsman 45378)
inch folding hex key set with 8 hex keys (Craftsman 49269)
metric folding hex key set with 8 hex keys (Craftsman 4927)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for Craftsman Extreme Grip Sockets from the 903-Piece Mechanics Tool Set

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the extreme grip style sockets from the Craftsman 903-pc set 21470.

Possible Modifications

Minimum trimmable size:

11 X 15-7/8 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site