FoamFit Tools section divider

Foam Tool Organizer for
10 Craftsman TruGrip Pliers with 3 Locking Pliers

see all organizers for pliers


10 Craftsman TruGrip Pliers with 3 Locking Pliers

Fits (4) pliers, (1) diagonal cutter, (3) mini pliers, (2) arc-joint pliers, and (3) locking pliers.

Accommodates the pliers from sets 71649, 28074, and 45713.

Only fits pliers with the "TruGrip" style handles.

Drawer Size
22-1/4 X 16-1/4 inches


FoamFit Tools section divider


7 inch diagonal cutter(Craftsman 28202)
7 inch linesman (Craftsman 71631)
8 inch long nose (Craftsman 28110)
8 inch long reach (Craftsman 71647)
6-3/4 inch slip joint (Craftsman 28075)
7 inch arc-joint (Craftsman 28452)
9-1/2 arc-joint (Craftsman 28346)
4 inch mini end nipper (Craftsman 45667)
4-1/2 inch mini long nose (Craftsman 45664)
4 inch mini diagonal cutter (Craftsman 45663)
6 inch long nose locking pliers (Craftsman 6LN, 45716)
7 inch locking pliers (Craftsman 7WR, 45710)
10 inch locking pliers (Craftsman 10R, 45715)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 10 Craftsman TruGrip Pliers and 3 Craftsman Locking Pliers

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the Craftsman 8-pc pliers set 71649, 2-pc arc-joint set 28074 and 3-pc locking pliers set 45713. The pockets are sized to fit pliers with "TruGrip" style handles, and locking pliers with the black and red plastic handles.

Possible Modifications

Minimum trimmable size:

21-1/4 X 15-5/8 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site