FoamFit Tools section divider

Foam Tool Organizer for
27 Craftsman Extreme Grip Adjustable and Ignition Wrenches with Hammer

see all organizers for specialty wrenches


27 Craftsman Extreme Grip Adjustable and Ignition Wrenches with Hammer

Fits (5) extreme grip style wrenches, (2) locking adjustable wrenches, (20) ignition wrenches, and (1) flex claw hammer

Accommodates the extreme grip, locking adjustable, and ignition wrenches plus the hammer from the Craftsman 903-pc set 21470.

Drawer Size
22-1/4 X 16-1/4 inches


FoamFit Tools section divider


3/8, 10mm extreme grip wrench (Craftsman 12759)
7/16, 11mm extreme grip wrench (Craftsman 15415)
1/2, 12mm, or 13mm extreme grip wrench (Craftsman 12760)
9/16, 14mm extreme grip wrench (Craftsman 12761)
5/8, 15mm, or 16mm extreme grip wrench (Craftsman 12762)
8-inch extreme grip locking adjustable wrench (Craftsman 42354)
10-inch extreme grip locking adjustable wrench (Craftsman 13272)

inch ignition wrenches sizes:
5/32 (Craftsman 42320)
3/16 (Craftsman 42321)
13/64 (Craftsman 42322)
7/32 (Craftsman 42323)
15/64 (Craftsman 42324)
1/4 (Craftsman 42325)
9/32 (Craftsman 42326)
5/16 (Craftsman 42327)
3/8 (Craftsman 42328)
7/16 (Craftsman 42329)

metric ignition wrenches sizes:
4 (Craftsman 42340)
4.5 (Craftsman 42341)
5 (Craftsman 42342)
5.5 (Craftsman 42343)
6 (Craftsman 42344)
7 (Craftsman 42345)
8 (Craftsman 42346)
9 (Craftsman 42347)
10 (Craftsman 42348)
11 (Craftsman 42349)

18oz flex claw hammer (Craftsman 50845)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for Craftsman Extreme Grip Wrenches, Flex Claw Hammer, and Additional Wrenches from the 903-Piece Mechanics Tool Set

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the extreme grip style wrenches, ignition wrenches, and hammer from the Craftsman 903-pc set 21470.

Possible Modifications

Minimum trimmable size:

21-3/4 X 16 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site