Fits (14) hex bit sockets, (21) torx bit sockets, (7) screwdriver bit sockets, (20) ignition wrenches, (51) screwdriver bits, (12) nut driver bits, (40) hex keys, and (3) additional tools.
Accommodates the hex, torx, and screwdriver bit sockets plus the ignition wrenches, screwdriver bits, and hex keys from the Husky 432-pc set H432MTS.
Drawer Size
20-3/8 X 15-11/16 inches
$49.50
larger image
note: tools are not included
Precision CNC-cut to fit 168 small Husky tools:
(7) 3/8-drive hex bit socket sizes from 1/8 to 3/8
(7) 3/8-drive hex bit socket sizes from 3 to 8 plus 10
(5) 1/4-drive torx bit socket sizes from T9 to T25
(7) 3/8-drive torx bit socket sizes T20 and T27 to T55
(9) 3/8-drive security (tamper) torx bit socket sizes from T15 to T55
(3) 3/8-drive phillips bit socket sizes #1, #2, #3
(3) 3/8-drive slotted screwdriver bit socket sizes 4, 5, 6mm
(1) 3/8-drive square (pozi) screwdriver bit socket size #2
(10) ignition (stubby/midget) wrench sizes from 5/32 to 7/16
(10) ignition (stubby/midget) wrench sizes from 4 to 11
(4) phillips screwdriver bit sizes from #1 to #4
(4) slotted screwdriver bit sizes from 1/8 to 5/16
(5) slotted screwdriver bit sizes from 3 to 6.5mm
(6) hex screwdriver bit sizes from 1/8 to 5/16
(8) hex screwdriver bit sizes from 2.5 to 8 plus 10mm
(4) square screwdriver bit sizes from #0 to #3
(4) pozi screwdriver bit sizes from #1 to #4
(8) torx screwdriver bit sizes from T10 to T45
(8) tamper torx screwdriver bit sizes from T10 to T45
(6) nut driver bit sizes from 1/4 to 1/2
(6) nut driver bit sizes 6 and 8 to 12mm
(10) short arm inch hex keys in holder
(10) short arm metric hex keys in holder
(10) long arm inch hex keys in holder
(10) long arm metric hex keys in holder
magnetic bit driver
1/4 X 5/16 double box-end (ratcheting) wrench
5/16 male hex to 1/4-drive socket adapter
This tool organizer was designed to fit the hex keys, screwdriver bits, ignition wrenches, hex bit sockets, and torx bit sockets from the Husky 432-pc set H432MTS.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
20-3/8 X 15-11/16 inches (inside width by inside depth)
Works in most drawers, needing no more than 2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
19-7/8 X 15-7/16 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.