Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
11 Snap-on Instinct Slotted Screwdrivers with Ratcheting Screwdriver Set
Overview
11 Snap-on Instinct Slotted Screwdrivers with Ratcheting Screwdriver Set
Fits 11 flat-tip screwdrivers including (5) standard, (4) cabinet, and (2) mini-tip. Also fits (1) ratcheting handle with (2) magnetic holders and (5) bits.
Fits screwdrivers from 4 popular sets when used with F-02849-R.
Drawer Size
14-1/2 X 21-7/8 inches
$49.30
Details
- Drawer size: 14-1/2 X 21-7/8 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 19 Snap-on screwdrivers, holders, and bits:
Slotted Mini-Tip:
1/8 X 3 (Snap-on SGD304B)
3/16 X 3 (Snap-on SGD306B)
Slotted Stubby:
1/4 X 1-7/8 (Snap-on SHD1)
Slotted Standard:
7/32 X 3 (Snap-on SGD2B)
1/4 X 4 (Snap-on SGD4B)
5/16 X 6 (Snap-on SGD6B)
3/8 X 8 (Snap-on SGD8B)
Slotted Cabinet:
3/16 X 6 (Snap-on SGD146B)
7/32 X 8 (Snap-on SGD480B)
7/32 X 12 (Snap-on SGD4120B)
7/32 X 16 (Snap-on SGD4160B)
Ratcheting Set SGDMRC103A:
Ratcheting Handle (Snap-on SGDMRC4A)
4-inch Magnetic Shank/Bit Holder (Snap-on SGDMRC4-40)
8-inch Magnetic Shank/Bit Holder (Snap-on SGDMRC4-80)
3/16 Flat-Tip Bit (Snap-on SDM211B)
9/32 Flat-Tip Bit (Snap-on SDM213B)
P1 Bit (Snap-on SDM221IRB)
P2 Bit (Snap-on SDM222IRB)
T15 Bit (Snap-on SDMT15B)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit Snap-on Instinct screwdrivers. Accommodates the flat-tip screwdrivers from standard set SGDX80B, cabinet set SGDXL80B, mini-tip set SGDX40B, and 8 pieces from ratcheting set SGDMRC103A.
Possible Modifications
Minimum trimmable size:
14 X 21-11/16 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-02848-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
