Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
15 Snap-on Instinct Phillips and Torx Screwdrivers
Overview
15 Snap-on Instinct Phillips and Torx Screwdrivers
Fits 10 Phillips screwdrivers including (4) standard, (4) cabinet, and (2) mini-tip. Also fits (5) torx screwdrivers.
Fits screwdrivers from 4 popular sets when used with F-02848-R.
Drawer Size
14-1/2 X 21-7/8 inches
$49.30
Details
- Drawer size: 14-1/2 X 21-7/8 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 15 Snap-on screwdrivers:
Phillips Mini Tip:
P0 X 3 (Snap-on SGDP300B)
P1 X 3 (Snap-on SGDP301B)
Phillips Stubby:
P2 X 1-5/8 Stubby (Snap-on SHDP22IR)
Phillips Standard:
P1 X 3 (Snap-on SGDP31IRB)
P2 X 4 (Snap-on SGDP42IRB)
P3 X 6 (Snap-on SGDP63IRB)
Phillips Cabinet:
P1 X 6 (Snap-on SGDP61B)
P2 X 8 (Snap-on SGDP82B)
P2 X 12 (Snap-on SGDP122B)
P2 X 16 (Snap-on SGDP162B)
Torx Standard:
T15 X 3 (Snap-on SGDTX315B)
T20 X 3 (Snap-on SGDTX320B)
T25 X 4 (Snap-on SGDTX425B)
T27 X 4 (Snap-on SGDTX427B)
T30 X 4 (Snap-on SGDTX430B)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit Snap-on Instinct screwdrivers. Accommodates the Phillips screwdrivers from standard set SGDX80B, cabinet set SGDXL80B, mini-tip set SGDX40B, and P3 X 6 screwdriver SGDP63IRB. Also fits the torx screwdrivers from standard-length set SGDTX50B.
Possible Modifications
Minimum trimmable size:
14 X 21-11/16 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-02849-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
