FoamFit Tools section divider

Foam Tool Organizer for
5 Nupla Hammers, 1 Mayhew Pry Bar, and 9 Mayhew Punches

see all organizers for Nupla and Mayhew tools


5 Nupla Hammers, 1 Mayhew Pry Bar, and 9 Mayhew Punches

Fits (5) hammers, including (2) ball pein hammers, (1) pry bar, and (9) punches, including (5) pin punches.

May be trimmed to fit a variety of drawer sizes.

Caution: Recommended for a 3-inch or deeper drawer.

Drawer Size
24 X 18 inches


FoamFit Tools section divider


12 oz ball pein (Nupla 21-012)
16 oz ball pein (Nupla 21-016)
16 oz soft face hammer (Nupla 11235, CBH-135)
20 oz rip claw hammer (Nupla 17-020)
2 lb dead blow (Nupla Power Drive 10025)
12 inch pry bar, 17 inch overall (Mayhew Dominator 60144)
center punch, 3/8 X 5 inch (Mayhew #415, size 3/8)
line-up punch, 5/32 X 9 (Mayhew 22011, #466, size 5/32)
cold chisel, 1/2 X 6 (Mayhew #70, size 1/2)
pin punch, 1/8 X 4-3/4 (Mayhew #413, size 1/8)
pin punch, 5/32 X 5 (Mayhew #413, size 5/32)
pin punch, 3/16 X 5-1/4 (Mayhew #413, size 3/16)
pin punch, 7/32 X 5-1/2 (Mayhew #413, size 7/32)
pin punch, 1/4 X 5-3/4 (Mayhew #413, size 1/4)
brass drift punch, 1/2 X 7 (Mayhew 25076)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 5 Nupla Hammers and 10 Mayhew Tools

note: tools are not included

Tool Requirements

This tool organizer insert may be trimmed to fit a variety of drawer sizes. The minimum size is marked on the drawing (see link below).

Possible Modifications

Minimum trimmable size:

22 X 14-7/8 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

Contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site