FoamFit Tools section divider

Foam Tool Organizer for
37 Husky Screwdrivers, Hard Handle Style, Version 1

see all organizers for Husky tools


37 Husky Screwdrivers, Hard Handle Style, Version 1

Fits (17) slotted screwdrivers, (8) Phillips screwdrivers, (6) Torx screwdrivers, (2) square screwdrivers, (2) offset screwdrivers, and (2) pocket screwdrivers.

Accommodates the screwdrivers from the 1025-pc Husky set H1025MTS.

Only fits the version where the handle is round nearest the blade.

Drawer Size
31-7/8 X 18-1/2 inches


FoamFit Tools section divider


P3 X 6 (H3X6PHSD)
P2 X 8 (H2X8PHSD)
P2 X 6 (H2X6PHSD)
P2 X 4 (H2X4PHSD)
P2 X 1-1/2 (H2X121SPHSD)
P1 X 3 (H1X3PHSD)
P1 X 1-1/2 (H1X112SPHSD)
P0 X 2-1/2 (H0X212PSD)

3/8 X 16 (H38X16FHSD)
3/8 X 12 (H38X12FHSD)
3/8 X 8 (H38X8FHSD)
5/16 X 8 (H516X8FHSD)
5/16 X 6 (H516X6FHSD)
1/4 X 6 (H14X6FHSD)
1/4 X 4 (H14X4FHSD)
3/16 X 9 (H316X9FHSD)
3/16 X 8 (H316X8CFHSD)
3/16 X 6 (H316X6FHSD)
3/16 X 4 (H316X4FHSD)
3/16 X 4 (H316X4CFHSD)
1/8 X 6 (H18X6FHSD)
1/8 X 4 (H18X4FHSD)
1/8 X 2 (H18X2FHSD)
1/4 X 1-1/2 (H114X112SFHSD)
3/16 X 1-1/2 (H316X112SFHSD)

T10 X 3
T15 X 3
T20 X 3
T25 X 4
T27 X 4
T30 X 4

S2 x 4 (H2X4SQSD)
S1 x 4 (H1X4SQSD)

2-piece offset (H2PCOSSDS)
2-piece micro (H2PCMICROSDS)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 37 Husky Hard-Handle Screwdrivers

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the screwdrivers from the 1025-pc Husky set H1025MTS. It does not fit the Husky 37-pc screwdriver set because those screwdrivers use a slightly larger 6-lobe handle design.

Possible Modifications

Minimum trimmable size:

31 X 18-3/16 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

Contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site