FoamFit Tools section divider

Foam Tool Organizer for
3 Craftsman Gunmetal Ratchets with 96 Additional Tools

see all organizers for drive tools


3 Craftsman Gunmetal Ratchets with 96 Additional Tools

Fits (3) ratchets, (13) drive accesories, (39) bits, and (44) hex keys.

Accommodates ratchets and drive tools from the Craftsman 282-piece gunmetal chrome mechanics tool set CMMT45282.

Drawer Size
22-1/4 X 14-1/2 inches


FoamFit Tools section divider


1-4-drive spinner handle (Craftsman 83-440)
1/4-drive 120-tooth pear head ratchet (Craftsman 82-010)
3/8-drive 120-tooth pear head ratchet (Craftsman 82-011)
1/2-drive 120-tooth pear head ratchet (Craftsman 82-012)

3-inch extension bar, 1/4-drive (Craftsman 82-021)
6-inch extension bar, 1/4-drive (Craftsman 82-022)
3-inch extension bar, 3/8-drive (Craftsman 82-024)
6-inch extension bar, 3/8-drive (Craftsman 82-025)
2.5-inch extension bar, 1/2-drive (Craftsman 82-027)
5-inch extension bar, 1/2-drive (Craftsman 82-028)

1/4-drive universal joint (Craftsman 82-014)
3/8-drive universal joint (Craftsman 82-015)
1/2-drive universal joint (Craftsman 82-016)

3/8-drive to 1/4 socket adapter (Craftsman 82-018)
1/2-drive to 3/8 socket adapter (Craftsman 82-020)
1/4-drive to 1/4 hex bit adapter (Craftsman 81-872)
(22) screwdriver bits in two holders

(14) hex keys from 3/64 to 5/16 in holder
(14) hex keys from 1.5 to 7 mm in holder
(8) short arm hex keys from 1/16 to 1/4 in holder
(8) short arm hex keys from 1.5 to 6 mm in holder

(8) nut driver bits from 3/16 to 1/2 in
(9) nut driver bits from 4 to 12mm

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 99 Craftsman Gunmetal Drive Tools and Accessories

note: tools are not included

Craftsman Gunmetal Chrome Markings

Tool Requirements

This tool organizer was designed to fit the ratchets, drive accessories, bits, and hex keys from the Craftsman 282-pc gunmetal chrome set CMMT45282.

Possible Modifications

Minimum trimmable size:

21-3/4 X 13-1/16 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site