FoamFit Tools section divider

Foam Tool Organizer for
48 Eklind Hex and Torx Keys

see all organizers for Eklind tools


48 Eklind Hex and Torx Keys

Fits (22) hex keys in holders, (19) T-handle hex keys, and (7) Torx keys in holder.

Shown with Eklind hex key sets 13213 and 13609, Power-T sets 64808, and Torx set 10007.

Sized to fit long-version L-key sets and 9-inch Power-T sets. Additional sets with regular ends, ball ends, and bright finish may also be used.

Drawer Size
34 X 22 inches


FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 48 Eklind Hex and Torx Keys:

T-handle hex keys:
5/64, 3/32, 7/64, 1/8 , 9/64, 5/32, 3/16, 7/32, 1/4 , 5/16, 3/8
2, 2.5, 3, 4, 5, 6, 8, 10 mm

long hex keys in holder:
.050, 1/16, 5/64, 3/32, 7/64, 1/8 , 9/64, 5/32, 3/16, 7/32, 1/4 , 5/16, 3/8
1.5, 2, 2.5, 3, 4, 5, 6, 8, 10 mm

Torx keys in holder:
T10, T15, T20, T25, T27, T30, T41

This tool organizer was designed to fit long hex-L keys and 9-inch Power-T hex keys. Shown with Eklind sets 60811, 64808, 13213, 13609, and 10007.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 48 Eklind Hex and Torx Keys

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

34 X 22 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 30 X 17-1/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site