Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
27 Tekton Inch Combination and Stubby Wrenches, Fits Version 1
Overview
27 Tekton Inch Combination and Stubby Wrenches, Fits Version 1
Fits (19) inch combination wrenches and (8) stubby inch wrenches.
Only fits earlier version with smaller 11/32 and 3/8 wrenches.
Sized to fit the Tekton 36 X 24 inch tool cabinet (ORG72200 or ORG72100). Please measure your drawer before ordering.
Drawer Size
31-7/16 X 20-9/16 inches
$95.40
Details
- Drawer size: 31-7/16 X 20-9/16 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 27 Tekton wrenches:
inch combination sizes:
1/4 (Tekton 18251)
9/32 (Tekton 18252)
5/16 (Tekton 18253)
11/32 (Tekton 18254, only fits 5-5/8 inch long version)
3/8 (Tekton 18255, only fits 6-1/8 inch long version)
7/16 (Tekton 18256)
1/2 (Tekton 18257)
9/16 (Tekton 18258)
5/8 (Tekton 18259)
11/16 (Tekton 18261)
3/4 (Tekton 18262)
13/16 (Tekton 18263)
7/8 (Tekton 18264)
15/16 (Tekton 18265)
1 (Tekton 18266)
1-1/16 (Tekton 18267)
1-1/8 (Tekton 18268)
1-3/16 (Tekton 18269)
1-1/4 (Tekton 18271)
inch stubby sizes:
5/16 (Tekton 18043)
3/8 (Tekton 18045)
7/16 (Tekton 18046)
1/2 (Tekton 18047)
9/16 (Tekton 18048)
5/8 (Tekton 18049)
11/16 (Tekton 18051)
3/4 (Tekton 18052)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit Tekton wrench sets WCB1102 and WRN01066.
Possible Modifications
Minimum trimmable size:
29-1/8 X 20-1/8 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
Contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-03827-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
