FoamFit Tools section divider

Foam Tool Organizer for
31 Tekton Metric Combination and Stubby Wrenches

see all organizers for Tekton

Overview

31 Tekton Metric Combination and Stubby Wrenches

Fits (19) metric combination wrenches and (12) stubby metric wrenches.

Sized to fit the Tekton 36 X 24 inch tool cabinet (ORG72200 or ORG72100). Please measure your drawer before ordering.

Drawer Size
31-7/16 X 20-9/16 inches

$89.80



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 31 Tekton wrenches:

metric combination sizes:
6 mm (Tekton 18275)
7 mm (Tekton 18276)
8 mm (Tekton 18277)
9 mm (Tekton 18278)
10 mm (Tekton 18279)
11 mm (Tekton 18281)
12 mm (Tekton 18282)
13 mm (Tekton 18283)
14 mm (Tekton 18284)
15 mm (Tekton 18285, best fits 8-1/8 inch long version)
16 mm (Tekton 18286)
17 mm (Tekton 18287)
18 mm (Tekton 18288, only fits 9 inch long version)
19 mm (Tekton 18289)
20 mm (Tekton 18291, only fits 9-7/8 inch long version)
21 mm (Tekton 18292)
22 mm (Tekton 18293)
23 mm (Tekton 18294)
24 mm (Tekton 18295)

metric stubby sizes:
8 mm (Tekton 18063)
9 mm (Tekton 18064)
10 mm (Tekton 18065)
11 mm (Tekton 18066)
12 mm (Tekton 18067)
13 mm (Tekton 18068)
14 mm (Tekton 18069)
15 mm (Tekton 18071)
16 mm (Tekton 18072)
17 mm (Tekton 18073)
18 mm (Tekton 18074)
19 mm (Tekton 18075)

This tool organizer was designed to fit Tekton wrench sets WCB90205 and WRN01170. Some combination wrench lengths should be checked before ordering. See 15mm, 18mm, and 20mm lengths above.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 19 metric combination wrenches and 12 stubby metric wrenches.

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

31-7/16 X 20-9/16 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 30-5/16 X 17-1/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-03828-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site