Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
20 Tekton Screwdrivers, 26 Hex Keys, and 11 Pliers
Overview
20 Tekton Screwdrivers, 26 Hex Keys, and 11 Pliers
Fits (7) slotted screwdrivers, (7) Phillips screwdrivers, (6) torx screwdrivers, (26) hex keys, and (11) pliers.
Accomodates the high torque screwdrivers from 12-pc set DRV41216, 6-pc torx screwdriver set DHT91006, hex key set 25252, plus 2 individual screwdrivers and 11 pliers.
Sized to fit the Tekton 36 X 24 inch tool cabinet (ORG72100 or ORG72200). Please measure your drawer before ordering.
Drawer Size
31-7/16 X 20-9/16 inches
$95.40
Details
- Drawer size: 31-7/16 X 20-9/16 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 57 Tekton tools:
slotted:
1/4 X 1-1/2 (Tekton 26621)
1/8 X 4 (Tekton 26603)
3/16 X 4 (Tekton 26613)
1/4 X 4 (Tekton 26623)
5/16 X 4 (Tekton 26633)
3/16 X 8 (Tekton 26615)
1/4 X 8 (Tekton 26625)
Phillips:
#2 X 1-1/2 (Tekton 26671)
#0 X 4 (Tekton 26653)
#1 X 4 (Tekton 26663)
#2 X 4 (Tekton 26673)
#3 X 4 (Tekton 26683)
#1 X 8 (Tekton 26665)
#2 X 8 (Tekton 26675)
torx:
T10 X 4 (Tekton 26801)
T15 X 4 (Tekton 26802)
T20 X 4 (Tekton 26803)
T25 X 4 (Tekton 26804)
T27 X 4 (Tekton 26805)
T30 X 4 (Tekton 26806)
pliers:
7 inch wire stripper (Tekton 3797)
7 inch long nose pliers (Tekton PGF10007)
6-1/2 inch slip joint pliers (Tekton 37122)
7 inch diagonal cutting pliers (Tekton PCT00007)
10 inch groove joint pliers (Tekton 37524)
10 inch curved jaw locking pliers (Tekton PLK10010)
6 inch long nose locking pliers (Tekton PLK30006)
mini long nose pliers (Tekton PMN11001)
mini flat nose pliers (Tekton PMN21001)
mini diagonal cutting pliers (Tekton PMN54001)
mini bent long nose pliers (Tekton PMN11301)
inch hex keys in holders:
3/64, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16,
7/32, 1/4, 5/16, 3/8 in.
metric hex keys in holders:
1.27, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 8, 10 mm
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit sets DRV41216, DHT91006, individual screwdrivers 26633 and 26683, hex key set 25252, plus the 11 pliers listed above.
Possible Modifications
Minimum trimmable size:
30-15/16 X 20-5/16 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-03834-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
