Fits (8) inch box end wrenches, (11) metric box end wrenches, (4) inch ratcheting wrenches, and (6) metric ratcheting wrenches.
Only fits 45-degree offset box end wrenches and the long version of the flex ratcheting box end wrenches.
Sized to fit the Tekton 48 X 24 inch tool cabinet (ORG73100 or ORG73200). Please measure your drawer before ordering.
43-7/16 X 20-9/16 inches
note: tools are not included
Precision CNC-cut to fit 29 Tekton wrenches:
inch 45-degree offset box end sizes:
1/4 x 5/16 in. (Tekton WBE23306)
3/8 x 7/16 in. (Tekton WBE23310)
1/2 x 9/16 in. (Tekton WBE23313)
5/8 x 11/16 in. (Tekton WBE23316)
3/4 x 13/16 in. (Tekton WBE23319)
7/8 x 15/16 in. (Tekton WBE23322)
1 x 1-1/16 in. (Tekton WBE23325)
1-1/8 x 1-1/4 in. (Tekton WBE23329)
metric 45-degree offset box end sizes:
6 x 7 mm (Tekton WBE24306)
8 x 10 mm (Tekton WBE24308)
9 x 11 mm (Tekton WBE24309)
12 x 14 mm (Tekton WBE24312)
13 x 15 mm (Tekton WBE24313)
16 x 18 mm (Tekton WBE24316)
17 x 19 mm (Tekton WBE24317)
20 x 22 mm (Tekton WBE24320)
21 x 23 mm (Tekton WBE24321)
24 x 27 mm (Tekton WBE24324)
30 x 32 mm (Tekton WBE24330)
inch long flex ratcheting box end sizes:
5/16 x 3/8 in. (Tekton WRN77003)
7/16 x 1/2 in. (Tekton WRN77005)
9/16 x 5/8 in. (Tekton WRN77007)
11/16 x 3/4 in. (Tekton WRN77009)
metric long flex ratcheting box end sizes:
8 x 10 mm (Tekton WRN76103)
9 x 11 mm (Tekton WRN76105)
12 x 14 mm (Tekton WRN76107)
13 x 15 mm (Tekton WRN76109)
16 x 18 mm (Tekton WRN76111)
19 x 19 mm (Tekton WRN76113)
This tool organizer was designed to fit Tekton wrench sets WBE23408, WBE24411, WRN77062, and WRN77164.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
43-7/16 X 20-9/16 inches (inside width by inside depth)
Works in most drawers, needing no more than 2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
42-13/16 X 17-1/4 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.
For orders within the contiguous 48 US states.
Made in the USA!