FoamFit Tools section divider

Foam Tool Organizer for
29 Tekton Box End and Ratcheting Wrenches

see all organizers for Tekton


29 Tekton Box End and Ratcheting Wrenches

Fits (10) long flex ratcheting and (19) 45-degree offset box end wrenches.

Only fits 45-degree offset box end wrenches and the long version of the flex ratcheting box end wrenches.

Sized to fit the Tekton 36 X 24 inch tool cabinet (ORG72200 or ORG72100). Please measure your drawer before ordering.

Drawer Size
31-7/16 X 20-9/16 inches


FoamFit Tools section divider


inch 45-degree offset box end sizes:
1/4 x 5/16 in. (Tekton WBE23306)
3/8 x 7/16 in. (Tekton WBE23310)
1/2 x 9/16 in. (Tekton WBE23313)
5/8 x 11/16 in. (Tekton WBE23316)
3/4 x 13/16 in. (Tekton WBE23319)
7/8 x 15/16 in. (Tekton WBE23322)
1 x 1-1/16 in. (Tekton WBE23325)
1-1/8 x 1-1/4 in. (Tekton WBE23329)

metric 45-degree offset box end sizes:
6 x 7 mm (Tekton WBE24306)
8 x 10 mm (Tekton WBE24308)
9 x 11 mm (Tekton WBE24309)
12 x 14 mm (Tekton WBE24312)
13 x 15 mm (Tekton WBE24313)
16 x 18 mm (Tekton WBE24316)
17 x 19 mm (Tekton WBE24317)
20 x 22 mm (Tekton WBE24320)
21 x 23 mm (Tekton WBE24321)
24 x 27 mm (Tekton WBE24324)
30 x 32 mm (Tekton WBE24330)

inch long flex ratcheting box end sizes:
5/16 x 3/8 in. (Tekton WRN77003)
7/16 x 1/2 in. (Tekton WRN77005)
9/16 x 5/8 in. (Tekton WRN77007)
11/16 x 3/4 in. (Tekton WRN77009)

metric long flex ratcheting box end sizes:
8 x 10 mm (Tekton WRN76103)
9 x 11 mm (Tekton WRN76105)
12 x 14 mm (Tekton WRN76107)
13 x 15 mm (Tekton WRN76109)
16 x 18 mm (Tekton WRN76111)
19 x 19 mm (Tekton WRN76113)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 19 long flex ratcheting and 45-degree offset box end wrenches.

note: tools are not included

Tool Requirements

This tool organizer was designed to fit Tekton wrench sets WBE23408, WBE24411, WRN77062, and WRN77164.

Possible Modifications

Minimum trimmable size:

30-15/16 X 20-5/16 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site