FoamFit Tools section divider

Foam Tool Organizer for
28 Husky Metric Reversible, Nonreversible and Flex-Head Wrenches

see all organizers for Husky

Overview

28 Husky Metric Reversible, Nonreversible and Flex-Head Wrenches

Fits (6) metric reversible ratcheting wrenches, (15) metric non-reversible ratcheting wrenches, and (7) metric flex-head ratcheting wrenches.

Accommodates the metric reversible and non-reversible ratcheting wrenches from the Husky 815-pc set H815MTS

Drawer Size
31-7/8 X 18-1/2 inches

$87.00



FoamFit Tools section divider

Details

metric reversible ratcheting combination wrenches:
9 mm
10 mm (HRRW10MM)
12 mm (HRRW12MM)
13 mm (HRRW13MM)
14 mm (HRRW14MM)
15 mm (HRRW15MM)

metric non-reversible ratcheting wrenches:
8 mm (HRW8MM)
9 mm (HRW9MM)
10 mm (HRW10MM)
11 mm (HRW11MM)
12 mm (HRW12MM)
13 mm (HRW13MM)
14 mm (HRW14MM)
15 mm (HRW15MM)
16 mm (HRW16MM)
17 mm (HRW17MM)
18 mm (HRW18MM)
19 mm (HRW19MM)
20 mm (HRW20MM)
21 mm (HRW21MM)
22 mm (HRW22MM)

metric flex-head ratcheting wrenches:
8 mm
9 mm
10 mm (HFRW10MM)
12 mm (HFRW12MM)
13 mm (HFRW13MM)
14 mm (HFRW14MM)
15 mm (HFRW15MM)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 28 Husky 12-point metric ratcheting wrenches

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the metric reversible, non-reversible, and flex-head non-reversible ratcheting combination wrenches from the Husky 815-pc set H815MTS.

Possible Modifications

Minimum trimmable size:

30-1/2 X 17-5/8 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-03891-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site