Fits (16) non-reversible ratcheting wrenches, (12) reversible ratcheting wrenches, (12) flex-head ratcheting wrenches, and (7) stubby ratcheting wrenches.
Accommodates the inch ratcheting wrenches from the Husky 1025-pc set H1025MTS.
Recommended for 3-1/16 min drawer height.
Drawer Size
33-13/16 X 19-3/4 inches
$135.60
larger image
note: tools are not included
Precision CNC-cut to fit 47 Husky ratcheting wrenches:
non-reversible wrenches:
1/4 (HRW14)
5/16 (HRW516)
3/8 (HRW38)
7/16 (HRW716)
1/2 (HRW12)
9/16 (HRW916)
5/8 (HRW58)
11/16 (HRW1116)
3/4 (HRW34)
13/16 (HR1316)
7/8 (HRW78)
15/16 (HRW1516)
1 (HRW1)
1-1/16 (HRW1116)
1-1/8 (HRW118)
1-1/4 (HRW114)
flex-head wrenches
5/16
3/8 (HFRW38)
7/16 (HFRW716)
1/2 (HFRW12)
9/16 (HFRW916)
5/8 (HFRW58)
11/16
3/4
13/16
7/8
15/16
1 inch
reversible wrenches:
5/16
3/8 (HRRW38)
7/16 (HRRW716)
1/2 (HRRW12)
9/16 (HRRW916)
5/8 (HRRW58)
11/16
3/4
13/16
7/8
15/16
1 inch
stubby wrenches:
3/8 (HSTRW38)
7/16 (HSTRW716)
1/2 (HSTRW12)
9/16 (HSTRW916)
5/8 (HSTRW58)
11/16 (HSTRW1116)
3/4 (HSTRW34)
This tool organizer was designed to fit the inch ratcheting wrenches from the Husky 1025-pc set H1025MTS.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
33-13/16 X 19-3/4 inches (inside width by inside depth)
Recommended for a drawer with at least 3-1/16 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
30-15/16 X 18-5/16 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.