FoamFit Tools section divider

Foam Tool Organizer for
27 Tekton Metric Combination Wrenches

see all organizers for Tekton


27 Tekton Metric Combination Wrenches

Fits (27) metric combination wrenches from 6 to 32 mm.

Accommodates the metric combination wrenches from the Tekton 46-pc set WCB90301.

Caution: Recommended for a 3 inch or taller drawer.

Drawer Size
24 X 18 inches


FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 27 Tekton wrenches:

metric combination sizes:
6 mm (Tekton 18275)
7 mm (Tekton 18276)
8 mm (Tekton 18277)
9 mm (Tekton 18278)
10 mm (Tekton 18279)
11 mm (Tekton 18281)
12 mm (Tekton 18282)
13 mm (Tekton 18283)
14 mm (Tekton 18284)
15 mm (Tekton 18285, best fits 8-1/8 inch long version)
16 mm (Tekton 18286)
17 mm (Tekton 18287)
18 mm (Tekton 18288, only fits 9 inch long version)
19 mm (Tekton 18289)
20 mm (Tekton 18291, only fits 9-7/8 inch long version)
21 mm (Tekton 18292)
22 mm (Tekton 18293)
23 mm (Tekton 18294)
24 mm (Tekton 18295)
25 mm (Tekton WCB24025)
26 mm (Tekton WCB24026)
27 mm (Tekton WCB24027)
28 mm (Tekton WCB24028)
29 mm (Tekton WCB24029)
30 mm (Tekton WCB24030)
31 mm (Tekton WCB24031)
32 mm (Tekton WCB24032)

This tool organizer was designed to fit the wrenches from Tekton set WCB90204, or the metric wrenches from the 46-pc set WCB90301. Some wrench lengths should be checked before ordering. See 15mm, 18mm, and 20mm lengths above.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 27 Tekton Metric Combination Wrenches

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

24 X 18 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-5/8 X 15-15/16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site