FoamFit Tools section divider

Foam Tool Organizer for
16 GearWrench Long Metric Non-Reversible Ratcheting Wrenches

see all organizers for GearWrench wrenches

Overview

16 GearWrench Long Metric Non-Reversible Ratcheting Wrenches

Fits (16) metric ratcheting wrenches from 8 to 22 plus 24mm.

Sized to fit the GearWrench 120XP Universal Spline XL wrenches.

Accommodates the wrenches from GearWrench set 86427.

New!

Drawer Size
24 X 18 inches

$56.40



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 16 GearWrench wrenches:

metric sizes:
8 (GearWrench 86408)
9 (GearWrench 86409)
10 (GearWrench 86410)
11 (GearWrench 86411)
12 (GearWrench 86412)
13 (GearWrench 86413)
14 (GearWrench 86314)
15 (GearWrench 86415)
16 (GearWrench 86416)
17 (GearWrench 86417)
18 (GearWrench 86418)
19 (GearWrench 86419)
20 (GearWrench 86420)
21 (GearWrench 86421)
22 (GearWrench 86422)
24 (GearWrench 86424)

This tool organizer was designed to fit the longer GearWrench 120XP Universal Spline XL ratcheting combination wrenches. These 16 wrenches are available as GearWrench set 86427.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for GearWrench ratcheting wrenches.

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

24 X 18 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 22 X 15-1/16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-04065-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site