FoamFit Tools section divider

Foam Tool Organizer for
25 Craftsman Screwdrivers with 8 Torx Keys

see all organizers for Craftsman Screwdrivers


25 Craftsman Screwdrivers with 8 Torx Keys

Fits (6) slotted, (6) phillips, (4) torx, (1) pocket, (3) offset, (1) square screwdriver, (4) picks, and (8) torx keys.

Accommodates the screwdrivers and folding torx keys from the 543-pc mechanics set CMMT72000.

Drawer Size
22-1/4 X 14-1/2 inches


FoamFit Tools section divider


3/32 X 1-1/2
1/8 X 2-1/2 (CMHT65017)
3/16 X 4 (CMHT65021)
1/4 X 1-1/2 (CMHT65013)
1/4 X 4 (CMHT65014)
1/4 X 6 (CMHT65015)

P0 X 1-1/2
P0 X 2-1/2 (CMHT65000)
P1 X 3 (CMHT65002)
P2 X 1-1/2 (CMHT65003)
P2 X 4 (CMHT65004)
P2 X 6 (CMHT65005)

T10 X 3 (CMHT65035)
T15 X 3 (CMHT65036)
T20 X 3 (CMHT65037)
T25 X 4 (CMHT65038)

other tools:
(1) square #2 X 4 (CMHT65033)
(4) mini-picks
(3) offset screwdrivers
(1) pocket/keychain
(8) torx keys in folding set

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 21 Craftsman Screwdrivers, 4 picks and 8 torx keys

note: tools are not included

Tool Requirements

This tool organizer was designed to fit a folding torx key set and all the screwdrivers from the Craftsman 543-pc set CMMT72000. The screwdrivers are the same as the Craftsman 25-pc screwdriver set CMHT65046.

Possible Modifications

Minimum trimmable size:

21 X 14-1/4 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site