FoamFit Tools section divider

Foam Tool Organizer for
16 GearWrench Metric Reversible Ratcheting Wrenches

see all organizers for GearWrench wrenches

Overview

16 GearWrench Metric Reversible Ratcheting Wrenches

Fits (16) metric reversible ratcheting wrench sizes 8 to 25mm.

Accommodates the wrenches from GearWrench set 9602N or 9602RN.

Caution: Only fits the 72-tooth wrenches with reversing levers.

New!

Drawer Size
23-3/4 X 17-3/4 inches

$56.40



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 16 GearWrench wrenches:

8 (GearWrench 9608N)
9 (GearWrench 9609N)
10 (GearWrench 9610N)
11(GearWrench 9611N)
12 (GearWrench 9612N)
13 (GearWrench 9613N)
14 (GearWrench 9614N)
15 (GearWrench 9615N)
16 (GearWrench 9616N)
17 (GearWrench 9617N)
18 (GearWrench 9618N)
19 (GearWrench 9619N)
21 (GearWrench 9621N)
22 (GearWrench 9622N)
24 (GearWrench 9624N)
25 (GearWrench 9625N)

This tool organizer was designed to fit ratcheting wrenches from GearWrench 16-piece set 9602N or 9602RN. The pockets are sized to fit 72-tooth ratcheting wrenches with reversing levers.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for GearWrench Metric Reversible Ratcheting Wrenches

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

23-3/4 X 17-3/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-1/4 X 14-9/16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-04291-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site