FoamFit Tools section divider

Foam Tool Organizer for
23 Craftsman Combination Wrenches, Fits Version with Diagonal Markings

see all organizers for Craftsman wrenches


23 Craftsman Combination Wrenches, Fits Version with Diagonal Markings

Fits (12) inch combination wrenches and (11) metric combination wrenches.

Accommodates all wrenches from the Cratsman 308-piece mechanics set CMMT45938.

Only fits wrenches with diagonal lines marked on both sides of the word Craftsman.

Does not fit gunmetal chrome wrenches or V-series wrenches. Does not fit any wrenches sold by Sears.


Drawer Size
22-1/4 X 16-1/4 inches


FoamFit Tools section divider


inch sizes:
1/4 (Craftsman CMMT44699)
5/16 (Craftsman CMMT44691)
11/32 (Craftsman CMMT44692)
3/8 (Craftsman CMMT44693)
7/16 (Craftsman CMMT44694)
1/2 (Craftsman CMMT44695)
9/16 (Craftsman CMMT44696)
5/8 (Craftsman CMMT44697)
11/16 (Craftsman CMMT44698)
3/4 (Craftsman CMMT44701)
7/8 (Craftsman CMMT44703)
15/16 (Craftsman CMMT44704)

metric sizes:
7mm (Craftsman CMMT12081)
8mm (Craftsman CMMT42912)
10mm (Craftsman CMMT42914)
12mm (Craftsman CMMT42916)
13mm (Craftsman CMMT42917)
14mm (Craftsman CMMT42918)
15mm (Craftsman CMMT42919)
16mm (Craftsman CMMT42924)
17mm (Craftsman CMMT42929)
18mm (Craftsman CMMT42925)
19mm (Craftsman CMMT42921)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for all Combination Wrenches From Craftsman 308-pc Mechanics Tool Set

note: tools are not included

Tool Requirements

This tool organizer was designed to fit all the wrenches from the Craftsman 308-piece set CMMT45938. These wrenches are a newer design with diagonal lines marked on both sides of the word Craftsman. This organizer will not fit gunmetal chrome wrenches, V-series wrenches, or any wrenches sold by Sears.

Possible Modifications

Minimum trimmable size:

22 X 15-5/8 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site