FoamFit Tools section divider

Foam Tool Organizer for
27 Tekton Inch Combination and Stubby Wrenches, Fits Version 2

see all organizers for Tekton

Overview

27 Tekton Inch Combination and Stubby Wrenches, Fits Version 2

Fits (19) inch combination wrenches and (8) stubby inch wrenches.

Only fits newer version with larger 11/32 and 3/8 wrenches.

Sized to fit the Tekton 36 X 24 inch tool cabinet (ORG72200 or ORG72100). Please measure your drawer before ordering.

New!

Drawer Size
31-7/16 X 20-9/16 inches

$95.40



FoamFit Tools section divider

Details

inch combination sizes:
1/4 (Tekton 18251)
9/32 (Tekton 18252)
5/16 (Tekton 18253)
11/32 (Tekton 18254, only fits 6-1/8 inch long version)
3/8 (Tekton 18255, only fits 6-5/16 inch long version)
7/16 (Tekton 18256)
1/2 (Tekton 18257)
9/16 (Tekton 18258)
5/8 (Tekton 18259)
11/16 (Tekton 18261)
3/4 (Tekton 18262)
13/16 (Tekton 18263)
7/8 (Tekton 18264)
15/16 (Tekton 18265)
1 (Tekton 18266)
1-1/16 (Tekton 18267)
1-1/8 (Tekton 18268)
1-3/16 (Tekton 18269)
1-1/4 (Tekton 18271)

inch stubby sizes:
5/16 (Tekton 18043)
3/8 (Tekton 18045)
7/16 (Tekton 18046)
1/2 (Tekton 18047)
9/16 (Tekton 18048)
5/8 (Tekton 18049)
11/16 (Tekton 18051)
3/4 (Tekton 18052)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 19 inch combination wrenches and 8 stubby inch wrenches.

note: tools are not included

Tool Requirements

This tool organizer was designed to fit Tekton wrench sets WCB1102 and WRN01066.

Possible Modifications

Minimum trimmable size:

29-1/8 X 20-1/8 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

Contact customer service to order this organizer in a special color.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-04631-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site