Contact Us |
Drawing and Part Number Lookup
920-569-0140
27 Tekton Inch Wrenches and 14 Nut Drivers, Fits Version 2
Fits (19) inch combination wrenches, (8) stubby inch wrenches, (7) inch nut drivers, and (7) metric nut drivers.
Only fits newer version with larger 11/32 and 3/8 wrenches.
Sized to fit the Tekton 48 X 24 inch tool cabinet (ORG73100 or ORG73200). Please measure your drawer before ordering.
Caution: some nut drivers are no longer made.
Drawer Size
43-7/16 X 20-9/16 inches
$144.20
inch combination sizes:
1/4 (Tekton 18251)
9/32 (Tekton 18252)
5/16 (Tekton 18253)
11/32 (Tekton 18254, only fits 6-1/8 inch long version)
3/8 (Tekton 18255, only fits 6-5/16 inch long version)
7/16 (Tekton 18256)
1/2 (Tekton 18257)
9/16 (Tekton 18258)
5/8 (Tekton 18259)
11/16 (Tekton 18261)
3/4 (Tekton 18262)
13/16 (Tekton 18263)
7/8 (Tekton 18264)
15/16 (Tekton 18265)
1 (Tekton 18266)
1-1/16 (Tekton 18267)
1-1/8 (Tekton 18268)
1-3/16 (Tekton 18269)
1-1/4 (Tekton 18271)
inch stubby sizes:
5/16 (Tekton 18043)
3/8 (Tekton 18045)
7/16 (Tekton 18046)
1/2 (Tekton 18047)
9/16 (Tekton 18048)
5/8 (Tekton 18049)
11/16 (Tekton 18051)
3/4 (Tekton 18052)
inch nut driver sizes:
3/16 (Tekton 26862)
1/4 (Tekton 26863)
5/16 (Tekton 26864)
11/32 (Tekton 26865)
3/8 (Tekton 26866)
7/16 (Tekton 26867)
1/2 (Tekton 26868)
metric nut driver sizes:
5mm (Tekton 26882)
5.5mm (Tekton 26883)
6mm (Tekton 26884)
7mm (Tekton 26885)
8mm (Tekton 26886)
9mm (Tekton 26887)
10mm (Tekton 26888)
This tool organizer was designed to fit Tekton wrench sets WCB90104 and WRN01066, plus nut driver sets 26964 and 26974.
42-13/16 X 20-1/8 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
black/yellow, black/green, black/gray
Contact customer service to order this organizer in a special color.
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.