FoamFit Tools section divider

Foam Tool Organizer for
27 Tekton Metric Combination Wrenches, Fits Version 2

see all organizers for Tekton

Overview

27 Tekton Metric Combination Wrenches, Fits Version 2

Fits (27) metric combination wrenches from 6 to 32 mm.

Accommodates the metric combination wrenches from the Tekton 46-pc set WCB90301.

Only fits newer version with longer 18, 20, and 23 mm wrenches.

Caution: Recommended for a 3 inch or taller drawer.

New!

Drawer Size
24 X 18 inches

$79.70



FoamFit Tools section divider

Details

metric combination sizes:
6 mm (Tekton 18275)
7 mm (Tekton 18276)
8 mm (Tekton 18277)
9 mm (Tekton 18278)
10 mm (Tekton 18279)
11 mm (Tekton 18281)
12 mm (Tekton 18282)
13 mm (Tekton 18283)
14 mm (Tekton 18284)
15 mm (Tekton 18285)
16 mm (Tekton 18286)
17 mm (Tekton 18287)
18 mm (Tekton 18288, only fits 9-3/8 inch long version)
19 mm (Tekton 18289)
20 mm (Tekton 18291, only fits 10-1/4 inch long version)
21 mm (Tekton 18292)
22 mm (Tekton 18293)
23 mm (Tekton 18294, fits 12 or 12-1/8 inch long version)
24 mm (Tekton 18295)
25 mm (Tekton WCB24025)
26 mm (Tekton WCB24026)
27 mm (Tekton WCB24027)
28 mm (Tekton WCB24028)
29 mm (Tekton WCB24029)
30 mm (Tekton WCB24030)
31 mm (Tekton WCB24031)
32 mm (Tekton WCB24032)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 27 Tekton Metric Combination Wrenches

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the wrenches from Tekton set WCB90204, or the metric wrenches from the 46-pc set WCB90301. It only fits newer sets with longer 18, 20, and 23 mm wrenches. Please measure the length of these three wrenches because the shorter wrenches won't fit as well.

Possible Modifications

Minimum trimmable size:

21-5/8 X 15-15/16 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

Contact customer service to order this organizer in a special color.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-04639-T.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site