FoamFit Tools section divider

Foam Tool Organizer for
15 Husky Screwdrivers with 62 Hex and Torx Keys

see all organizers for Husky tools


15 Husky Screwdrivers with 62 Hex and Torx Keys

Fits (5) slotted screwdrivers, (6) Phillips screwdrivers, (4) Torx screwdrivers, (25) Torx keys, (9) inch hex keys, and (28) metric hex keys.

Accommodates the screwdrivers, hex keys, and torx keys, from the Husky 505-pc set H505MTSPO.


Drawer Size
19-1/2 X 21-11/16 inches


FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 77 Husky tools:

3/16 X 1-1/2
3/16 X 4
1/4 X 4
1/4 X 6
5/16 X 8

P1 X 1-1/2
P1 X 3
P2 X 4
P2 X 6
P2 X 8
P3 X 6

T10 X 3
T15 X 3
T20 X 3
T25 X 4

(9) Tamperproof Torx L-Key Set
(8) Folding Tamperproof Torx Set
(8) Folding Torx Set
(9) Folding Inch Hex Key Set
(8) Folding Metric Hex Key Set
(10) Metric Short Hex Key Set
(10) Metric Long Hex Key Set

This tool organizer was designed to fit the screwdrivers, hex keys, and torx keys from the Husky 505-pc set H505MTSPO.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 15 Husky Screwdrivers and 62 Hex and Torx Keys

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

19-1/2 X 21-11/16 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 18 X 21-7/16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site