Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
19 Craftsman Slotted Screwdrivers, Hard Handles
Overview
19 Craftsman Slotted Screwdrivers, Hard Handles
Fits (19) slotted screwdrivers.
Accommodates the slotted screwdrivers from the 42-piece set CMHT65300.
Drawer Size
22-1/4 X 16-1/4 inches
$53.40
Details
- Drawer size: 22-1/4 X 16-1/4 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 19 Craftsman screwdrivers:
1/8 X 2-1/2 (CMHT65017)
1/8 X 4 (CMHT65018)
1/8 X 6 (CMHT65019)
3/16 X 4 (CMHT65021)
3/16 X 4 cabinet tip (CMHT65022)
3/16 X 6 (CMHT65023)
3/16 X 6 cabinet tip (CMHT65024)
3/16 X 8 cabinet tip (CMHT65084)
3/16 X 9 (CMHT65025)
1/4 X 1-1/2 (CMHT65013)
(2) 1/4 X 4 (CMHT65014)
1/4 X 6 (CMHT65015)
1/4 X 8 (CMHT65016)
5/16 X 6 (CMHT65030)
5/16 X 8 (CMHT65031)
3/8 X 8 (CMHT65026)
3/8 X 12 (CMHT65027)
3/8 X 16 (CMHT65028)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit roughly half of the screwdrivers from the 42-piece Craftsman screwdriver set CMHT65300. The 42-pc set was new in 2022 and older Craftsman screwdrivers may not fit.
Possible Modifications
Minimum trimmable size:
21-9/16 X 14-1/4 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
Contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-05066-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
