Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
23 Craftsman Phillips and Other Screwdrivers, Hard Handles
Overview
23 Craftsman Phillips and Other Screwdrivers, Hard Handles
Fits (12) Phillips screwdrivers, (3) square-tip screwdrivers, (7) torx screwdrivers, and (1) scratch awl.
Accommodates the Phillips, torx, and square screwdrivers from the 42-piece set CMHT65300.
Drawer Size
22-1/4 X 14-1/2 inches
$49.80
Details
- Drawer size: 22-1/4 X 14-1/2 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 23 Craftsman screwdrivers:
Phillips:
P0 X 2-1/2 (CMHT65000)
(2) P1 X 3 (CMHT65002)
P2 X 1-1/2 (CMHT65003)
(2) P2 X 4 (CMHT65004)
P2 X 6 (CMHT65005)
P2 X 8 (CMHT65006)
P2 X 12 (CMHT65007)
P2 X 16 (CMHT65008)
P3 X 6 (CMHT65009)
P4 X 8 (CMHT65010)
Torx:
T6 x 2 (CMHT65034)
T10 X 3 (CMHT65035)
T15 X 3 (CMHT65036)
T20 X 3 (CMHT65037)
T25 X 4 (CMHT65038)
T27 X 4 (CMHT65039)
T30 X 4 (CMHT65040)
Other:
square #1 X 4 (CMHT65104)
square #2 X 4 (CMHT65033)
square #3 X 6 (CMHT65091)
scratch awl (CMHT65012)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit roughly half of the screwdrivers from the 42-piece Craftsman screwdriver set CMHT65300. The 42-pc set was new in 2022 and older Craftsman screwdrivers may not fit.
Possible Modifications
Minimum trimmable size:
21-3/4 X 14-1/4 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
Contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-05067-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
