Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
27 Husky Inch Combination and Stubby Wrenches with 72 Bits and Driver
Overview
27 Husky Inch Combination and Stubby Wrenches with 72 Bits and Driver
Fits (19) inch combination wrenches from 1/4 to 1-1/2, (8) stubby wrenches, (1) magnetic handle, and (72) screwdriver bits.
Accommodates the inch combination and stubby wrenches, plus the screwdriver bits and magnetic handle from the Husky 1025-pc set H1025MTS.
Caution: Recommended for a 2-3/4 inch or deeper drawer.
Drawer Size
31-1/2 X 17 inches
$105.10
Details
- Drawer size: 31-1/2 X 17 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 100 Husky tools:
inch combination wrenches:
1/4 (HSPW14)
5/16 (HSPW516)
11/32 (HSPW1132)
3/8 (HSPW38)
7/16 (HSPW716)
1/2 (HSPW12)
9/16 (HSPW916)
5/8 (HSPW58)
11/16 (HSPW1116)
3/4 (HSPW34)
13/16 (HCW1316)
7/8 (HSPW78)
15/16 (HCW1516)
1 (HCW1)
1-1/16 (HCW1116)
1-1/8 (HCW118)
1-1/4 (HCW114)
1-5/16 (HCW1516)
1-1/2 (HCW112)
stubby wrenches:
1/4 (HSTW14)
3/8 (HSTW38)
7/16 (HSTW716)
1/2 (HSTW12)
9/16 (HSTW916)
5/8 (HSTW58)
11/16 (HSTW1116)
3/4 (HSTW34)
bit accessories:
(1)magnetic handle
(6) inch nut driver bits 1/4 to 1/2
(6) metric nut driver bits 6 to 12 mm
(6) inch hex bits
(8) metric hex bits
(8) torx bits
(8) security torx bits
(9) slotted bits
(4) square bits
(13) Phillips bits
(4) pozi bits
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This organizer was designed to fit the inch combination and stubby wrenches plus the magnetic handle and screwdriver bits from the Husky 1025-pc set H1025MTS or H1025MTSPO.
Possible Modifications
Minimum trimmable size:
30-15/16 X 16-5/8 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
Contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-05082-T.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
