FoamFit Tools section divider

Foam Tool Organizer for
23 Husky Inch Wrenches with 46 Hex Keys, 72 Bits, and Magnetic Handle

see all organizers for Husky tools

Overview

23 Husky Inch Wrenches with 46 Hex Keys, 72 Bits, and Magnetic Handle

Fits (17) combination wrenches from 1/4 to 1-1/4, (5) stubby wrenches from 3/8 to 11/16, trailer hitch wrench, magnetic handle, (72) screwdriver bits, and (46) hex keys.

Accommodates the inch combination wrenches and additional tools from the Husky 605-pc set H605MTSPO.

Caution: Recommended for a 2-3/4 inch or deeper drawer.

New!

Drawer Size
31-1/2 X 17 inches

$105.10



FoamFit Tools section divider

Details

inch combination wrenches:
1/4
5/16
11/32
3/8
7/16
1/2
9/16
5/8
11/16
3/4
13/16
7/8
15/16
1
1-1/16
1-1/8
1-1/4

inch stubby wrenches:
3/8
1/2
9/16
5/8
11/16

trailer hitch wrench:
1-1/8 X 1-1/2

hex keys:
(10) short inch
(13) long inch
(10) short metric
(13) long metric

other:
magnetic handle
(6) inch nut driver bits 1/4 to 1/2
(6) metric nut driver bits 6 to 12 mm
(6) inch hex bits
(8) metric hex bits
(8) torx bits
(8) security torx bits
(9) slotted bits
(4) square bits
(13) Phillips bits
(4) pozi bits

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 17 Husky Inch Combination Wrenches, 5 Stubby Wrenches, 46 Hex Keys, and 74 Additional Tools

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the inch combination and stubby wrenches from the Husky 605-pc set H605MTSPO. It also fits the hex keys, trailer hitch wrench, magnetic handle, and screwdriver bits.

Possible Modifications

Minimum trimmable size:

30-15/16 X 16-3/4 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

Contact customer service to order this organizer in a special color.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-05093-T.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site