Fits the Tekton 56-pc set SKT05303, 6-pc nut driver set DHD91101, and 5-pc nut driver set DHD91201.
Fits (22) inch sockets, (28) metric sockets, 1/4-drive ratchet, (5) drive tools, (6) inch nut drivers, and (5) metric nut drivers.
Only fits the newer 1/4-drive set which includs a black spinner handle with red ends.
23-3/4 X 17-3/4 inches
note: tools are not included
Precision CNC-cut to fit 67 Tekton tools:
sockets from the 1/4-drive set:
(11) 1/4-drive deep 6-point sizes from 5/32 to 9/16
(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(14) 1/4-drive deep 6-point sizes from 4 to 15 mm
(14) 1/4-drive 6-point sizes from 4 to 15 mm
drive tools from the 1/4-drive set:
1/4-drive 90-tooth quick-release ratchet (Tekton SRH11006)
1/4-drive 6-inch spinner handle (Tekton SHH03125)
1/4 X 3 extension (Tekton SHA01103)
1/4 X 6 extension (Tekton SHA01106)
1/4-drive universal joint (Tekton SHA02100)
1/4-drive magnetic hex bit holder (Tekton SHA05402)
from nut driver set DHD91101:
3/16 (Tekton 26862)
1/4 (Tekton 26863)
5/16 (Tekton 26864)
3/8 (Tekton 26866)
7/16 (Tekton 26867)
1/2 (Tekton 26868)
from nut driver set DHD91201:
6 mm (Tekton 26884)
7 mm (Tekton 26885)
8 mm (Tekton 26886)
9 mm (Tekton 26887)
10 mm (Tekton 26888)
This tool organizer was designed to fit the 1/4-drive sockets, ratchet, and drive tools from the Tekton 56-pc set SKT05303. This newer version of the 1/4-drive set includes 15 mm sizes and has a black spinner handle with red ends. It also fits the Tekton High-Torque nut drivers from the 6-pc inch set DHD91101 and the 5-pc metric set DHD91201.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
23-3/4 X 17-3/4 inches (inside width by inside depth)
Works in most drawers, needing no more than 2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
22 X 15-1/4 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.
For orders within the contiguous 48 US states.
Made in the USA!