Fits the Tekton 56-pc set SKT05303 and 73-pc set SKT15311.
Fits (52) inch sockets, (66) metric sockets, (2) ratchets, 3/8 X 18 breaker bar, (4) extensions, and (4) additional drive tools.
Recommended for 3 min drawer height.
Drawer Size
23-3/4 X 17-3/4 inches
$85.60
larger image
note: tools are not included
Precision CNC-cut to fit 129 Tekton tools:
from the 1/4-drive set:
(11) 1/4-drive deep 6-point sizes from 5/32 to 9/16
(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(14) 1/4-drive deep 6-point sizes from 4 to 15 mm
(14) 1/4-drive 6-point sizes from 4 to 15 mm
1/4-drive 90-tooth quick-release ratchet (Tekton SRH11006)
1/4-drive 6-inch spinner handle (Tekton SHH03125)
1/4 X 3 extension (Tekton SHA01103)
1/4 X 6 extension (Tekton SHA01106)
1/4-drive universal joint (Tekton SHA02100)
1/4-drive magnetic hex bit holder (Tekton SHA05402)
from the 3/8-drive set:
(15) 3/8-drive deep 6-point sizes from 1/4 to 1 inch
(15) 3/8-drive 6-point sizes from 1/4 to 1 inch
(19) 3/8-drive deep 6-point sizes from 6 to 24 mm
(19) 3/8-drive 6-point sizes from 6 to 24 mm
3/8-drive 90-tooth quick-release ratchet (Tekton SRH11108)
3/8 X 18 breaker bar (Tekton SBH00118)
3/8 X 3 extension (Tekton SHA11103)
3/8 X 6 extension (Tekton SHA11106)
3/8-drive universal joint (Tekton SHA12101)
This tool organizer was designed to fit the 1/4-drive tools from the Tekton 56-pc set SKT05303 plus the 3/8-drive tools from the Tekton 73-pc set SKT15311. These two sets are also included in the 212-piece Tekton bundle SKT95304.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
23-3/4 X 17-3/4 inches (inside width by inside depth)
Recommended for a drawer with at least 3 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
20-15/16 X 14-1/16 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.