Fits the Tekton 212-pc mechanics set SKT95304.
Fits (84) inch sockets, (112) metric sockets, (3) ratchets, and (13) additional drive tools.
Fits all the tools from the 56-pc 1/4-drive set SKT05303, 73-pc 3/8-drive set SKT15311, and 83-pc 1/2-drive set SKT25302.
Recommended for 3-1/2 min drawer height.
36-5/8 X 19-1/2 inches
note: tools are not included
Precision CNC-cut to fit 212 Tekton tools:
from the 1/4-drive set:
(11) 1/4-drive deep 6-point sizes from 5/32 to 9/16
(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(14) 1/4-drive deep 6-point sizes from 4 to 15 mm
(14) 1/4-drive 6-point sizes from 4 to 15 mm
1/4-drive 90-tooth quick-release ratchet (Tekton SRH11006)
1/4-drive 6-inch spinner handle (Tekton SHH03125)
1/4 X 3 extension (Tekton SHA01103)
1/4 X 6 extension (Tekton SHA01106)
1/4-drive universal joint (Tekton SHA02100)
1/4-drive magnetic hex bit holder (Tekton SHA05402)
from the 3/8-drive set:
(15) 3/8-drive deep 6-point sizes from 1/4 to 1 inch
(15) 3/8-drive 6-point sizes from 1/4 to 1 inch
(19) 3/8-drive deep 6-point sizes from 6 to 24
(19) 3/8-drive 6-point sizes from 6 to 24
3/8-drive 90-tooth quick-release ratchet (Tekton SRH11108)
3/8 X 18 breaker bar (Tekton SBH00118)
3/8 X 3 extension (Tekton SHA11103)
3/8 X 6 extension (Tekton SHA11106)
3/8-drive universal joint (Tekton SHA12101)
from the 1/2-drive set:
(16) 1/2-drive deep 6-point sizes from 3/8 to 1-5/16
(16) 1/2-drive 6-point sizes from 3/8 to 1-5/16
(23) 1/2-drive deep 6-point sizes from 10 to 32 mm
(23) 1/2-drive 6-point sizes from 10 to 32 mm
1/2-drive 90-tooth quick-release ratchet (Tekton SRH11210)
1/2 X 18 breaker bar (Tekton SBH00218)
1/2 X 3 extension (Tekton SHA21103)
1/2 X 10 extension (Tekton SHA21110)
1/2-drive universal joint (Tekton SHA22102)
This tool organizer was designed to fit all the tools from the 212-pc Tekton set SKT95304. The 212-pc set is three sets combined, so the Tekton 56-pc set SKT05303, 73-pc set SKT15311, and 83-pc set SKT25302 would also fit. This organizer has been updated to fit the newer black spinner handle with red ends. It also includes pockets for two 1/4-drive 15 mm sockets which were recently added to the 1/4-drive set.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
36-5/8 X 19-1/2 inches (inside width by inside depth)
Recommended for a drawer with at least 3-1/2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
36 X 16-1/4 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.
For orders within the contiguous 48 US states.
Made in the USA!